OOBM-MAD commands
vsf oobm-mad
Syntax
[no] vsf oobm-mad
Description
Enable OOBM-MAD (Multi-Active Detection) on the VSF device.
Options
oobm vsf member
Syntax
oobm vsf member
<MEMBER-ID>
ip
address <IP-ADDR>/<PREFIX-LENGTH>
Description
Configure VSF member OOBM parameters.
Syntax
oobm vsf member
<MEMBER-ID>
ip
default-gateway <IP-ADDR>
Description
Specify the default gateway using this form of
the command. Configure the IPv4 default gateway address, which will
be used when routing is not enabled on the switch. The <IP-ADDR>
must
be specified if the command is not preceded by [no]
.
Preceding the command with [no]
deletes the default
gateway address.The [no]
form of this command does
not take effect on default gateway address obtained via dhcp.
Options
VSF | Configure VSF member OOBM parameters. |
member | Configure VSF member OOBM parameters. |
<1-2> | The VSF member-ID for the 'member' command/parameter. |
IP | Configure various IP parameters for the OOBM. |
IP-ADDR | IPv4 address of the default gateway. |
address | Set IP parameters for communication within an IP network. |
Usage
oobm vsf member
<VSF-MEMBER>
ip
oobm vsf member
<VSF-MEMBER>
ip
address
[no] ip default-gateway
<IP-ADDR>
oobm vsf member interface speed-duplex
Syntax
oobm vsf member
<VSF-MEMBER>
interface <SPEED-DUPLEX>
Description
Configure various interface parameters for OOBM.
The interface
command must be followed by a feature-specific
keyword. This is an OOBM context command. It can be called directly
from the OOBM context.
Options
enable | Enable OOBM port. |
disable | Disable OOBM. |
member | Configure VSF member OOBM parameters. |
speed-duplex | Define mode of operation for the oobm port. |
Usage
interface [enable|disable|speed-duplex]
oobm vsf member
<VSF-MEMBER>
interface
enable
oobm vsf member
<VSF-MEMBER>
interface
disable
show OOBM
Syntax
show oobm
Description
Show the global OOBM configuration.
show OOBM
vsf-sws# show oobm Global OOBM Configuration OOBM Enabled : Yes VSF Member 1 OOBM Port Type : 100/1000T OOBM Interface Status : Up OOBM Port : Enabled OOBM Port Speed : Auto MAC Address : 3464a9-b24301 VSF Member 2 OOBM Port Type : 100/1000T OOBM Interface Status : Up OOBM Port : Enabled OOBM Port Speed : Auto MAC Address : 288023-98ae01
show OOBM vsf member
Syntax
show oobm vsf
member
<VSF-MEMBER-LIST>
Description
Show OOBM VSF member.
Options
show OOBM IP
Syntax
show oobm ip
Description
Show OOBM IP.
Options
show oobm ip
show oobm ip IPv4 Status : Enabled IPv4 Default Gateway : 120.93.49.1 | Address Interface VSF-member | IP Config IP Address/Prefix Length Status Status ---------- + --------- ------------------------- -------- --------- Global | dhcp 120.93.49.9/24 Active Up 1 | dhcp 120.93.49.9/24 Active Up 2 | disabled Inactive Down
show oobm ip vsf member 1
HP-VSF-Switch# show oobm ip vsf member 1 IPv4 Status : Enabled IPv4 Default Gateway : 15.212.178.1 | Address Interface VSF-member | IP Config IP Address/Prefix Length Status Status ---------- + --------- ------------------------- -------- --------- 1 | dhcp 15.212.178.244/24 Active Up
show oobm ip vsf member 1,2
HP-VSF-Switch(config)# sho oobm ip vsf member 1,2 IPv4 Status : Enabled IPv4 Default Gateway : | Address Interface VSF-member | IP Config IP Address/Prefix Length Status Status ---------- + --------- ------------------------- -------- --------- 1 | dhcp Active Down HP-VSF-Switch(config)# sho oobm ip detail Internet (IP) Service for OOBM Interface Global Configuration IPv4 Status : Enabled IPv6 Status : Disabled IPv4 Default Gateway : IPv6 Default Gateway : Origin | IP Address/Prefix Length Status ---------- + ------------------------------------------- ----------- dhcp | VIPv4 SF Member 1 Status : Enabled IPv6 Status : Disabled IPv4 Default Gateway : IPv6 Default Gateway : Origin | IP Address/Prefix Length Status ---------- + ------------------------------------------- ----------- dhcp |
Usage
show oobm ip vsf member
<MEMBER-LIST>
show oobm ip detail
show OOBM discovery
Syntax
show oobm discovery
Description
Show the discovered virtual chassis information.
show running-config OOBM
Syntax
show running-config
oobm
Description
Show running-config OOBM.
show running-config oobm
show running-config oobm Running configuration: oobm ip address dhcp-bootp VSF-member 1 ip address dhcp-bootp exit VSF-member 2 ip address 192.168.10.1 255.255.255.0 exit exit
show vsf trunk-designated-forwarder
Syntax
show vsf trunk-designated-forwarder
Description
Show the designated forwarders for each trunk.
For each trunk, only one member of the trunk
will forward L2 flood traffic (unknown destination, Broadcast &
Multicast). Use the show vsf trunk-designated-forwarder
command
to know which member will forward flood frames for a given trunk.
For known unicast traffic, trunks will always forward using local member links when possible and traffic will cross the VSF links to the other member only when local links of a trunk are down.
Usage
show vsf trunk-designated-forwarder
Validation rules
Validation |
Error/Warning/Prompt |
---|---|
If you have a VSF switch and you download a non-VSF config or a VSF-config that is invalid for the current VSF switch, they must be blocked. |
The configuration file for this VSF device is incorrect. |
When you enable VSF, the hostname of the virtual chassis would change to a different string than it is when VSF is disabled |
HP-5406R-VSF |