Contents
-
Ethernet interface configuration commands -
-
broadcast-suppression -
combo enable -
default -
description -
display counters -
display counters rate -
display interface -
display loopback-detection -
display port-group manual -
display storm-constrain -
duplex -
flow-control -
flow-control receive enable -
flow-interval -
group-member -
interface -
jumboframe enable -
link-delay -
link-delay mode up -
loopback -
loopback-detection action -
loopback-detection control enable -
loopback-detection enable -
loopback-detection interval-time -
loopback-detection multi-port-mode enable -
loopback-detection per-vlan enable -
mdi -
multicast-suppression -
port-group manual -
reset counters interface -
shutdown -
speed -
speed auto -
storm-constrain -
storm-constrain control -
storm-constrain enable log -
storm-constrain enable trap -
storm-constrain interval -
unicast-suppression -
virtual-cable-test
-
-
Loopback and null interface configuration commands -
Bulk interface configuration commands -
MAC address table configuration commands -
MAC Information configuration commands -
Ethernet link aggregation configuration commands -
-
default -
description -
display interface -
display lacp system-id -
display link-aggregation load-sharing mode -
display link-aggregation member-port -
display link-aggregation summary -
display link-aggregation verbose -
enable snmp trap updown -
interface bridge-aggregation -
lacp period short -
lacp system-priority -
link-aggregation load-sharing mode -
link-aggregation mode -
link-aggregation port-priority -
link-aggregation selected-port minimum -
port link-aggregation group -
reset counters interface -
reset lacp statistics -
shutdown
-
-
Port isolation configuration commands -
Spanning tree configuration commands -
-
active region-configuration -
bpdu-drop any -
check region-configuration -
display stp -
display stp abnormal-port -
display stp bpdu-statistics -
display stp down-port -
display stp history -
display stp region-configuration -
display stp root -
display stp tc -
instance -
region-name -
reset stp -
revision-level -
snmp trap enable stp -
stp bpdu-protection -
stp bridge-diameter -
stp compliance -
stp config-digest-snooping -
stp cost -
stp edged-port -
stp enable -
stp loop-protection -
stp max-hops -
stp mcheck -
stp mode -
stp no-agreement-check -
stp pathcost-standard -
stp point-to-point -
stp port bpdu-protection -
stp port priority -
stp port shutdown permanent -
stp port-log -
stp priority -
stp region-configuration -
stp root primary -
stp root secondary -
stp root-protection -
stp tc-protection -
stp tc-protection threshold -
stp tc-snooping -
stp timer forward-delay -
stp timer hello -
stp timer max-age -
stp timer-factor -
stp transmit-limit -
vlan-mapping modulo
-
-
BPDU tunneling configuration commands (available only on the HPE 3100 v2 EI) -
VLAN configuration commands -
Voice VLAN configuration commands (available only on the HPE 3100 v2 EI) -
GVRP configuration commands -
QinQ configuration commands -
VLAN mapping configuration commands (available only on the HPE 3100 v2 EI) -
LLDP configuration commands -
-
display lldp local-information -
display lldp neighbor-information -
display lldp statistics -
display lldp status -
display lldp tlv-config -
lldp admin-status -
lldp check-change-interval -
lldp compliance admin-status cdp (available only on the HPE 3100 v2 EI) -
lldp compliance cdp (available only on the HPE 3100 v2 EI) -
lldp enable -
lldp encapsulation snap -
lldp fast-count -
lldp hold-multiplier -
lldp management-address-format string -
lldp management-address-tlv -
lldp notification remote-change enable -
lldp timer notification-interval -
lldp timer reinit-delay -
lldp timer tx-delay -
lldp timer tx-interval -
lldp tlv-enable
-
-
MVRP commands -
Document conventions and icons -
Support and other resources