Ports Events
The following are the events related to ports.
Event ID: 76
Message | port <PORT_ID> is now on-line |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | Indicates the port changed from an off-line to on-line state. To be on-line, the port must be both connected into the LAN and enabled through configuration. <id> is a letter-digit identifier (for example, A1 F3) where the letter represents the port module slot (A thru F) and the digit represents the port on the slot (1 thru 4 for Ethernet modules and 1 thru 2 for 100VG). |
Event ID: 77
Message | port <PORT_ID> is now off-line |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | Indicates the port changed from an on-line to off-line state. This occurs when the port is physically disconnected from the LAN, disabled through configuration, or both. <id> is a letter-digit identifier (for example, A1, F3) where the letter represents the port module slot (A thru F) and the digit represents the port on the slot (1 thru 4 for Ethernet modules and 1 thru 2 for 100VG). |
Event ID: 78
Message | trunk <TRUNK_ID> is now active |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | Indicates the port trunk has changed from an inactive to active state. This occurs when all ports in the trunk are off-line; and then one port comes on-line. <id> is always "Tr1" since there can be only one port trunk on the switch. |
Event ID: 79
Message | trunk <TRUNK_ID> is now inactive |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | Indicates the port trunk has changed from an active to inactive state. This occurs when the last on-line port in the trunk goes off-line such that there are now no ports in the trunk that are on-line. <id> is always "Tr1" since there can be only one port trunk on the switch. |
Event ID: 255 (Severity: Warning)
Message | Cannot configure trunk <TRUNK_ID> - out of resources |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | Cannot configure trunk TRUNK-ID; out of resources. |
Event ID: 256
Message | Port <PORT_NUM> is reserved for <EVENT_MSG> use |
Platforms | KB, WB, WC |
Category | Ports |
Severity | Information |
Description | This message displays during port-stealing. |
Event ID: 257
Message | Port <PORT_NUM> is unreserved from <EVENT_MSG> use |
Platforms | KB, WB, WC |
Category | Ports |
Severity | Information |
Description | This message displays during port-unstealing. |
Event ID: 325 (Severity: Warning)
Message | Port initialization failed for port <PORT_NUM> |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | GVRP could not add a port to a VLAN because system has reached the maximum number of VPORT (port-vlan pairs) instances. |
Event ID: 326 (Severity: Warning)
Message | port <PORT_NUM>: Xcvr not supported in current OS |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | Port has been blocked on VLAN by PVST. |
Event ID: 335
Message | port <PORT_NUM>: exceeded threshold broadcast throttling started |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The port has exceeded threshold broadcast so throttling has been started. |
Event ID: 336
Message | port <PORT_NUM>: broadcast throttling stopped |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | Broadcast throttling has been stopped on the port. |
Event ID: 366 (Severity: Warning)
Message | port <PORT_NUM> Carrier Sense Stuck- Resetting Xcvr |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has sense stuck resetting xcvr. |
Event ID: 368 (Severity: Warning)
Message | port <PORT_NUM> Xcvr Error- Resetting Xcvr ... |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has error resetting xcvr. |
Event ID: 369 (Severity: Warning)
Message | port <PORT_NUM> Rx Signal/PLL Error- Resetting Xcvr R17: <ERROR ID> |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has signal pll error resetting xcvr r error id. |
Event ID: 370 (Severity: Warning)
Message | resetting port <PORT_NUM>: remote fault- ieee- parallel detect |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has remote fault ieee parallel detect. |
Event ID: 378
Message | port <PORT_NUM>: Slot <SLOT_ID> Interrupt <INTERUPT ID> |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | reports the interrupt and interrupt value of the module |
Event ID: 379
Message | port <PORT_NUM> in half duplex- flow control is auto-disabled. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The reason why the management port has half duplex flow control is auto disabled. |
Event ID: 405
Message | port <PORT_NUM> xcvr hot-swap insert. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The reason why the management port has hot swap insert. |
Event ID: 406
Message | port <PORT_NUM> xcvr hot-swap remove. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The reason why the management port has hot swap remove. |
Event ID: 407
Message | port <PORT_NUM> new xcvr invalid type and/or speed. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The reason why the management port has xcvr invalid type and or speed. |
Event ID: 408
Message | port <PORT_NUM> xcvr type change. Check switch config. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The reason why the management port has type change check switch config. |
Event ID: 409
Message | port <PORT_NUM> GigT xcvr invalid mode change. Need reboot. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The reason why the management port has xcvr invalid mode change need reboot. |
Event ID: 435
Message | port <PORT_NUM> is Blocked by <EVENT STR> |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | Indicates that the port is being blocked |
Event ID: 448 (Severity: Warning)
Message | port <PORT_NUM> disabled due to faulty link partner. Re-install module or reset switch prior to re-enabling port. |
Platforms | KB, WB, WC, YC |
Category | Ports |
Severity | Warning |
Description | The port was disabled due to faulty link partner. Re-install module or reset switch prior to re-enabling port. |
Event ID: 449
Message | port <PORT_NUM> RJ-45 is enabled. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The reason why the management port has is enabled. |
Event ID: 450
Message | port <PORT_NUM> mini-GBIC is enabled. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The reason why the management port has gbic is enabled. |
Event ID: 532 (Severity: Warning)
Message | port <PORT_NUM> Unsupported Transceiver. (SelfTest Err#<ERROR ID>) Check: http://www.arubanetworks.com/products/networking/ for more info. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | Unsupported Transceiver. |
Event ID: 533 (Severity: Warning)
Message | port <PORT_NUM> is not a <TYPE> transceiver. Please go to: http://www.arubanetworks.com/products/networking/ for more info. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | Unsupported OUI or SFP type verbiage |
Event ID: 534 (Severity: Warning)
Message | port <PORT_NUM> Transceiver type not supported in this software version. Please check for an updated release. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has type not supported in this software version please check for an updated release. |
Event ID: 535 (Severity: Warning)
Message | port <PORT_NUM> This switch only supports revision B and above transceivers. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has switch only supports revision b and above transceivers. |
Event ID: 536 (Severity: Warning)
Message | port <PORT_NUM> Transceiver type not supported in this port. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has type not supported in this port. |
Event ID: 560
Message | port <PORT_NUM> PD Detected. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The reason why the management port has detected. |
Event ID: 561
Message | port <PORT_NUM> Applying Power to PD. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The reason why the management port has power to pd. |
Event ID: 562 (Severity: Warning)
Message | port <PORT_NUM> PD Over Current indication. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has over current indication. |
Event ID: 563 (Severity: Warning)
Message | port <PORT_NUM> PD MPS Absent indication. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has mps absent indication. |
Event ID: 564 (Severity: Warning)
Message | port <PORT_NUM> PD Invalid Signature indication. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has invalid signature indication. |
Event ID: 565
Message | port <PORT_NUM> PD Removed. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The reason why the management port has removed. |
Event ID: 566 (Severity: Warning)
Message | port <PORT_NUM> PD Denied power due to insufficient power allocation. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has denied power due to insufficient power allocation. |
Event ID: 567 (Severity: Warning)
Message | port <PORT_NUM> PD Other Fault indication. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has other fault indication. |
Event ID: 580 (Severity: Warning)
Message | Port <PORT_NUM>: Attempt to recover from bad FET failed. The port will not deliver power. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has to recover from bad fet failed the port will not deliver power. |
Event ID: 632 (Severity: Warning)
Message | port <PORT_NUM> Duplex Mismatch. Reconfig port to Full Duplex. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has mismatch reconfig port to full duplex. |
Event ID: 633 (Severity: Warning)
Message | port <PORT_NUM> Duplex Mismatch. Reconfig port to Auto. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has mismatch reconfig port to auto. |
Event ID: 723 (Severity: Warning)
Message | port <PORT_NUM> both flow ctrl and jumbo frames enabled. Flow control may not function properly. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has flow ctrl and jumbo frames enabled flow control may not function properly. |
Event ID: 898
Message | <SYSTEM ID> has disabled port <PORT_NUMBER> for <TIMEOUT> seconds |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 899 (Severity: Warning)
Message | <SYSTEM ID> has disabled port <PORT_NUM> |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management id has port port num. |
Event ID: 900
Message | port <PORT_NUM> timer requested by <SYSTEM ID> has expired |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 927 (Severity: Warning)
Message | Port <PORT_ID> - Port Security configured on a 10Mbps port- packets will be dropped. Refer to switch manuals. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has security configured on a mbps port packets will be dropped refer to switch manuals. |
Event ID: 2562 (Severity: Warning)
Message | Port <PORT_NUM>: Possible bad FET/PSE supplying PoE power - suggest configuring other end of link with "no power" |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has bad fet pse supplying poe power suggest configuring other end of link with no power. |
Event ID: 2566 (Severity: Warning)
Message | Port <PORT_NUM>: Recovered from bad FET. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has from bad fet. |
Event ID: 2567 (Severity: Warning)
Message | Port <PORT_NUM>: Possible bad FET - suggest resetting with "power poe-reset". Or- PSE supplying PoE power - suggest configuring other end of link with "no power" |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has bad fet suggest resetting with power poe reset or pse supplying poe power suggest configuring other end of link with no power. |
Event ID: 2767 (Severity: Warning)
Message | port <PORT_NUM> detected non-HPID xcvr or DAC |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has non hpid xcvr or dac. |
Event ID: 2768 (Severity: Warning)
Message | Port <PORT_NUM> PoE power dropped. Exceeded physical classification for a PoE Type1 device (LLDP process disabled) |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has power dropped exceeded physical classification for a poe type device lldp process disabled. |
Event ID: 2770 (Severity: Warning)
Message | Port <PORT_NUM> EEE disabled due to Polarity Error found on the cable. Correct the polarity error for EEE to work. |
Platforms | KB, WB, WC, YA, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has disabled due to polarity error found on the cable correct the polarity error for eee to work. |
Event ID: 2771 (Severity: Warning)
Message | Port <PORT_NUM> PoE power dropped. Exceeded physical classification due to change in classification type (LLDP process enabled) |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has power dropped exceeded physical classification due to change in classification type lldp process enabled. |
Event ID: 2772 (Severity: Warning)
Message | EEE cannot be enabled on port <PORT_NUM> on this hardware revision- (link partner attempted to enable). |
Platforms | KB, WB, WC, YA, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management cannot has on port port num on this hardware revision link partner attempted to enable. |
Event ID: 3169 (Severity: Warning)
Message | Only <MAX_LIMIT> <PRODUCT_NUMBER> transceivers are supported in this module. The transceiver in port <PORT_NUM> has been disabled. Please remove this transceiver. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | Logs a port having a transceiver over its restriction limit. |
Event ID: 3700
Message | Non-HP transceiver detected in port <PORT_NUM>- which may cause network problems. HP will not support or troubleshoot problems with this transceiver. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The reason why the management hp has in port port num which may cause network problems hp will not support or troubleshoot problems with this transceiver. |
Event ID: 3701
Message | Ports <PORT_NUM> still has unsupported transceivers- which may cause network problems. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The reason why the management port has has unsupported transceivers which may cause network problems. |
Event ID: 3702
Message | Port <PORT_NUM> - port type change. The port configuration may need to be updated. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The reason why the management port has type change the port configuration may need to be updated. |
Event ID: 3703
Message | Port <PORT_NAME> unsupported xcvr hot-swap insert. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | A third party transceiver has been swapped into one of the transceiver bay. |
Event ID: 3704
Message | Allow-Unsupported-Transceiver feature enabled: |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | Unsupported Transceivers found in: <EVENT_MSG> List of Non-HPN transceiver has been present into the switch. |
Event ID: 3705
Message | Allow-Unsupported-Transceiver feature enabled. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | Allow-Unsupported-Transceiver feature enabled. |
Event ID: 4742 (Severity: Warning)
Message | PTP temporarily disabled on port <PORT_ID> - IEEE 1588 is not supported at the current link speed |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | Port <PORT_ID> is linked up with the speed at which we don't support IEEE1588 protocol |
Event ID: 4743
Message | Port <PORT_NUM> recovery occurred. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The reason why the management port has occurred. |
Event ID: 4744 (Severity: Warning)
Message | PTP disabled on all ports - the inserted module does not support IEEE 1588 |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 4745 (Severity: Warning)
Message | PTP disabled on all ports - this software version does not support enabling MACsec and IEEE 1588 at the same time |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 4776
Message | Connection-rate filter is disabled because meshing is enabled on port <PORT_ID>. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The reason why the management rate has disabled because meshing is enabled on port port id. |
Event ID: 5100 (Severity: Warning)
Message | port <PORT_NUM> encountered a UVLO fault and will attempt to recover itself by toggling power. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | The reason why the management port has a uvlo fault and will attempt to recover itself by toggling power. |
Event ID: 5176
Message | Port <PORT_NAME>: Configuring poe-value <POE_VALUE> to maximum supported value 30. |
Platforms | KB, WC, YC |
Category | Ports |
Severity | Information |
Description | If poe-value greater than 30 is configured in previous release, while upgrading to 16.01 it is converted to 30 and below log is generated- Port <PORT_NAME>: Configuring poe-value <POE_VALUE> to maximum supported value 30. |
Event ID: 5761 (Severity: Warning)
Message | Port <PORT_NAME_STRING> [chan <CHANNEL>]: Possible bad FET/PSE supplying PoE power - suggest configuring other end of link with "no power" |
Platforms | WC |
Category | Ports |
Severity | Warning |
Description | This log event informs the possible bad FET/PSE supplying PoE power - suggest configuring other end of link with "no power" on port on a channel |
Event ID: 5762 (Severity: Warning)
Message | Port <PORT_NAME_STRING> [chan <CHANNEL>]: Recovered from bad FET. |
Platforms | WC |
Category | Ports |
Severity | Warning |
Description | This log event informs to recover from bad FET. |
Event ID: 5763 (Severity: Warning)
Message | Port <PORT_NAME_STRING> [chan <CHANNEL>]: Attempt to recover from bad FET failed. The port will not deliver power. |
Platforms | WC |
Category | Ports |
Severity | Warning |
Description | This log event informs to attempt to recover from bad FET failed. The port will not deliver power. |
Event ID: 5764 (Severity: Warning)
Message | Port <PORT_NAME_STRING> [chan <CHANNEL>]: PD Over Current indication. |
Platforms | WC |
Category | Ports |
Severity | Warning |
Description | This log event informs the PD Over Current indication for port on a channel |
Event ID: 5773
Message | Port <PORT_NAME_STRING>: Dual Signature PD Detected. |
Platforms | WC |
Category | Ports |
Severity | Information |
Description | This log message is to indicate the dual signature PD Detected. |
Event ID: 5774
Message | Port <PORT_NAME_STRING> [chan <CHANNEL>]: Applying Power to PD. |
Platforms | WC |
Category | Ports |
Severity | Information |
Description | This log message is to indicate the applying Power to PD. |
Event ID: 5775 (Severity: Warning)
Message | Port <PORT_NAME_STRING> [chan <CHANNEL>]: PD MPS Absent indication. |
Platforms | WC |
Category | Ports |
Severity | Warning |
Description | This log message is to indicate the PD MPS Absent indication. |
Event ID: 5776 (Severity: Warning)
Message | Port <PORT_NAME_STRING> [chan <CHANNEL>]: PD Invalid Signature detected. |
Platforms | WC |
Category | Ports |
Severity | Warning |
Description | This log message is to indicate the PD Invalid Signature. |
Event ID: 5777
Message | Port <PORT_NAME_STRING> [chan <CHANNEL>]: PD Removed. |
Platforms | WC |
Category | Ports |
Severity | Information |
Description | This log message is to indicate the PD Removed. |
Event ID: 5778 (Severity: Warning)
Message | Port <PORT_NAME_STRING> [chan <CHANNEL>]: Power denied due to Power On Verification fault. |
Platforms | WC |
Category | Ports |
Severity | Warning |
Description | This log message is to indicate the power denied due to Power On Verification fault. |
Event ID: 5779 (Severity: Warning)
Message | Port <PORT_NAME_STRING>: PD power <CHANNEL>. Suggest using allocate-by-usage or allocate-by-class |
Platforms | WC |
Category | Ports |
Severity | Warning |
Description | This log message is to indicate the suggest using allocate-by-usage or allocate-by-class. |
Event ID: 5780
Message | Port <PORT_NAME_STRING> [chan <CHANNEL>]: Power demoted. |
Platforms | WC |
Category | Ports |
Severity | Information |
Description | This log message is to indicate the power demoted. |
Event ID: 5781
Message | Port <PORT_NAME_STRING>: 802.3bt non-compliant Dual Signature PD Detected. |
Platforms | WC |
Category | Ports |
Severity | Information |
Description | This log message is to indicate the 02.3bt non-compliant Dual Signature PD Detected. |
Event ID: 5782
Message | Port <PORT_NAME_STRING>: Power demoted. |
Platforms | WC |
Category | Ports |
Severity | Information |
Description | This log message is to indicate the power demoted. |
Event ID: 5783 (Severity: Warning)
Message | Port <PORT_NAME_STRING> [chan <CHANNEL>]: Power denied due to Power On Invalid Class Sequence. |
Platforms | WC |
Category | Ports |
Severity | Warning |
Description | This log message is to indicate the power denied event due to power On Invalid Class Sequence. |
Event ID: 5824
Message | Port <PORT_NAME_STR>: PD stopped responding to LLDP PoE TLVs from PSE. Previous LLDP negotiated power values will be retained. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 5864 (Severity: Warning)
Message | Total power drawn is exceeding the total POE power available. Suggest checking connected PDs and cabling to reduce the power draw. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 5886
Message | Port <PORT_NAME_STR>: Assigned class changed from class <CLASS_ID1> to class <CLASS_ID2> due to power request through LLDP PoE TLV. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |