System Events

The following are the events related to system.

Event ID: 61

Message
-----------------------------------------
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Information
Description This log even generates a blank line in the event log.

Event ID: 62

Message
SYSTEM went down without saving crash information
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Information
Description SYSTEM went down without saving crash information.

Event ID: 63

Message
SYSTEM went down: <REASON_STR>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Information
Description SYSTEM went down and the reason why is given.

Event ID: 64 (Severity: Fatal)

Message
<CRASH REASON STR>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Fatal

Event ID: 65 (Severity: Fatal)

Message
Boot-up selftest failed
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Fatal
Description This message displays if the boot up selftest resulted in a failure. A slot selftest failure message will also be logged for each slot that resulted in a failure.

Event ID: 66

Message
system: System Booted
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Information
Description This message displays at the conclusion of the boot process.

Event ID: 75 (Severity: Warning)

Message
Out of <BUF TYPE> buffers; miss count: <COUNT VAL>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Warning

Event ID: 260

Message
Mgmt Module <MODULE_ID> Active
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Information

Event ID: 261

Message
Mgmt Module <MODULE_ID> in Standby Mode
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Information

Event ID: 262 (Severity: Warning)

Message
Mgmt Module <MODULE_ID> Failed - Synchronization Failed
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Warning

Event ID: 263

Message
Mgmt Module <MODULE_ID> Offline (redundancy disabled)
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Information

Event ID: 264 (Severity: Warning)

Message
Mgmt Module <MODULE_ID> Failed Selftest
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Warning

Event ID: 265 (Severity: Warning)

Message
Lost Communication with Mgmt Module <MODULE_ID>
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Warning

Event ID: 266

Message
Resetting Mgmt Module <MODULE_ID>
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Information

Event ID: 267 (Severity: Warning)

Message
Mgmt Module <MODULE_ID> - Running different version of SW
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Warning

Event ID: 268 (Severity: Warning)

Message
Mgmt Module <MODULE_ID> - Failover occured
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Warning

Event ID: 269

Message
Mgmt Module <MODULE_ID> - User initiated switchover occured
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Information

Event ID: 270 (Severity: Warning)

Message
Mgmt Module <MODULE_ID> - Offline (Incompatible SW versions)
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Warning

Event ID: 271 (Severity: Warning)

Message
Other management module is not in standby- shutdown request ignored
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Warning

Event ID: 272

Message
Mgmt Module <MODULE_ID> Offline (shutdown)
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Information

Event ID: 273

Message
Resetting Mgmt Module <MODULE_ID> - <REASON_STR>
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Information
Description The reason why the management module <MODULE_ID> was reset is given.

Event ID: 542

Message
Runtime Error Skipped: <ERROR_MSG>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Information
Description Skips runtime error messages that are not being used.

Event ID: 543

Message
The command was terminated prematurely because the output exceeded the maximum memory limit.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Information

Event ID: 686 (Severity: Fatal)

Message
<UPGRADE_FAILED_REASON_STR>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Fatal

Event ID: 687

Message
<UPGRADE_PASSED_REASON_STR>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Information

Event ID: 820 (Severity: Warning)

Message
A signature is not stored with the current switch software. Please see the 'Software Signing and Verification' section of the Basic Operations Guide for details.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Warning

Event ID: 994 (Severity: Warning)

Message
<PORTS|MODULE> <ID> parity recovery <MEMORY_INDEX> 0x<LOCATION>.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Warning
Description Logs the successful repair of certain ASIC memory location that reported a (soft) parity error. Memory Index is the internal ASIC index of the particular memory bank (as there are many). This message is used by HPE Support.

Event ID: 995 (Severity: Warning)

Message
<PORTS|MODULE> <ID> parity recoveries in previous <INTERVAL_VAL>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Warning
Description Logs the number of successful recoveries that occurred during. the interval: 5 minutes; 1 hours; 24 hours. This reduces the number. of system log events when many recoveries happen close in time.

Event ID: 2681 (Severity: Warning)

Message
Workaround nic-82566dm occurred. See www.hp.com/networking/device_help/nic_update for details.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Warning
Description A NIC is transmitting excessive fragments. Possible Causes: A malfunctioning NIC. Actions:. 1. Check to see if switch is receiving fragments by issuing. "walkmib etherstatsFragments" from the switch CLI. 2. Update the NIC firmware. 3. Update the NIC Driver software. 4. By default; FFI will automatically downgrade the port speed to auto-10/100 if excessive fragments have been etected on the gig port. 5. Check www.procurve.com/device_help/nic_update for more details.

Event ID: 3001 (Severity: Fatal)

Message
System reboot due to Power Failure
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Fatal
Description This message displays when the switch goes through a reboot. because of a power failure.

Event ID: 3002 (Severity: Fatal)

Message
System reboot due to Switch Reset
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Fatal
Description This message displays when the switch goes through a soft reboot when the user executes the "boot system flash <primary|secondary>"

Event ID: 3003

Message
Configuration hash calculation started.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Information
Description This message displays when the hash generation for the running configuration is started

Event ID: 3004

Message
Configuration hash calculation finished.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Information
Description This message displays when the hash generation for the running configuration is finished

Event ID: 3005

Message
Diagnostic level is set to <SUPPORT|STARNDARD>
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Information

Event ID: 3006

Message
Reason for system reboot: <REBOOT_REASON_STR>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Information

Event ID: 3007 (Severity: Warning)

Message
message buffer allocation has reached <USAGE_PERCENTAGE>
Platforms KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Warning
Description This event is used to indicate when the message buffer usage reached above threshold limit.

Event ID: 3008 (Severity: Warning)

Message
packet buffer allocation has reached <USAGE_PERCENTAGE>
Platforms KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Warning
Description This event is used to indicate when the packet buffer usage reached above threshold limit.

Event ID: 3009 (Severity: Warning)

Message
packet buffer high priority allocation has reached <USAGE_PERCENTAGE>
Platforms KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Warning
Description This event is used to indicate when the packet high priority buffer usage reached above threshold limit.

Event ID: 3010 (Severity: Warning)

Message
packet message buffer high priority allocation has reached <USAGE_PERCENTAGE>
Platforms KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Warning
Description This event is used to indicate when packet message high priority buffer usage reached above threshold limit.

Event ID: 3011 (Severity: Warning)

Message
management message buffer allocation has reached <USAGE_PERCENTAGE>
Platforms KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Warning
Description This event is used to indicate when the management message buffer usage reached above threshold limit.

Event ID: 3012 (Severity: Warning)

Message
oobm packet buffer allocation has reached <USAGE_PERCENTAGE>
Platforms KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Warning
Description This event is used to indicate when the oobm buffer usage reached above threshold limit.

Event ID: 3361

Message
Note: As per RFC 1123- the hostname must contain only letters- numbers and hyphens- and must not start or end with a hyphen.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Information
Description RFC for protocols mandate that component hostname labels may contain only the ASCII letters 'a' through 'z' (in a case-insensitive manner), the digits '0' through '9', and the hyphen (-). The original specification of hostnames in RFC 952 mandated that labels could not start with a digit or with a hyphen and must not end with a hyphen. However; a subsequent specification (RFC 1123) permitted hostname labels start with digits. No other symbols, punctuation characters, or blank spaces are permitted.

Event ID: 3395 (Severity: Warning)

Message
<BUFFER_MSG>
Platforms KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Warning
Description Security Log message

Event ID: 3396 (Severity: Warning)

Message
<BUFFER_MSG>
Platforms KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Warning
Description Security Log message

Event ID: 3440

Message
User:'<USER_NAME>':The command: <AAAA_AUTH_SSH_ENABLE_RADIUS>
Platforms KB, WB, WC, YC
Category System
Severity Information
Description User:'user1': The command: 'aaa authentication ssh enable radius' is executed during boot up.

Event ID: 3441 (Severity: Warning)

Message
The command log buffer is 80% full.
Platforms KB, WB, WC, YC
Category System
Severity Warning
Description Log message is :The command log buffer is 80% full.

Event ID: 3442 (Severity: Warning)

Message
The command log buffer has wrapped; older logs will be overwritten.
Platforms KB, WB, WC, YC
Category System
Severity Warning
Description Log message is : The command log buffer has wrapped; older logs will be overwritten.

Event ID: 3443 (Severity: Warning)

Message
The event log buffer is 80% full.
Platforms KB, WB, WC, YC
Category System
Severity Warning
Description Log message is :The event log buffer is 80% full.

Event ID: 3444

Message
User:'<USER_NAME>': <COMMAND_LOG_INFO>
Platforms KB, WB, WC, YC
Category System
Severity Information
Description Log messages are: User:'user1': The command logging is enabled. User:'user1': The command logging completed.

Event ID: 3500

Message
The supportability information in file <FILENAME> is corrupt and has been removed
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Information
Description Informs that some of the crash/boot-history information has been corrupt and removed.

Event ID: 3801 (Severity: Warning)

Message
Mgmt Module <MODULE_ID> - Nonstop switching disabled because of SW version mismatch. Warm standby enabled.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Warning

Event ID: 3805

Message
<LOG STR>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Information
Description This event can be used for any banner related events Currently used for 'banner exec' and 'banner motd' banner exec; The banner exec message is modified. banner motd; Message of the day(MOTD) banner is modified. no banner exec; The banner exec message is disabled. no banner motd; Message of the day(MOTD) banner is disabled.

Event ID: 3841 (Severity: Fatal)

Message
<UPGRADE_FAIL_STATUS_MSG>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Fatal

Event ID: 3842

Message
<UPGRADE_PASS_STATUS_MSG>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Information

Event ID: 4180 (Severity: Warning)

Message
Auto reset value changed from <OLD_VALUE> to <NEW_VALUE>: <MESSAGE_STR>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Warning

Event ID: 4753

Message
Event log buffer has wrapped; older logs will be overwritten.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Information

Event ID: 5011

Message
Switch is in preview mode.
Platforms KB, WB, WC, YC
Category System
Severity Information

Event ID: 5041

Message
Active configuration backup has failed on enabling preview mode.
Platforms KB, WB, WC, YC
Category System
Severity Information

Event ID: 5042

Message
Restoring backup configuration to active configuration has failed on disabling preview mode. Active configuration has been erased.
Platforms KB, WB, WC, YC
Category System
Severity Information

Event ID: 5352

Message
One or more tunnels with unsupported tunnel ID- greater than <MAX_TUNNEL>- have been deleted from the configuration.
Platforms KA
Category System
Severity Information
Description This event is used to indicate the deletion of one or more invalid Tunnel IDs after downgrade to a version that does not support tunnek IDs greater than value specified in <MAX_TUNNEL>.

Event ID: 5353

Message
Exit Hibernation Mode.
Platforms KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Information
Description system: System reboot due to exiting Hibernation Mode. This message appears when the switch goes through a reboot because hibernation mode is being exited.

Event ID: 5561

Message
The tcp-push-preserve feature was disabled. This is a change to default configuration.
Platforms K, KA, KB, WB, WC, YC
Category System
Severity Information
Description This event is used to indicate that there is a default value change for "tcp-push-preserve" command from enable to disable on upgrade.

Event ID: 5575

Message
copp: Threshold exceeded for traffic class <CLASS_NAME>. Packets are being dropped.
Platforms KB, WC
Category System
Severity Information
Description This message displays when the rate at which a particular class of traffic is received at the switch exceeds the configured limit.

Event ID: 5576

Message
copp: Threshold exceeded for user defined copp - <ID>. Packets are being dropped.
Platforms KB, WC
Category System
Severity Information
Description This message displays when the rate at which a particular class of traffic is received at the switch exceeds the configured limit.

Event ID: 5577

Message
MM <MODULE_ID> elected as Active-MM based on preferred-amm configuration
Platforms KB
Category System
Severity Information

Event ID: 5579

Message
Port <PORT> with fault-finder broadcast-storm configuration cannot be added to a trunk.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category System
Severity Information
Description This event is used to indicate that fault-finder broadcast-storm is not allowed on a trunk port.

Event ID: 5580 (Severity: Warning)

Message
Fault-finder broadcast-storm configuration is removed as it is configured on a VSF port <PORT_NAME>.
Platforms KB, WC
Category System
Severity Warning
Description This event is used to indicate that fault-finder broadcast-storm is not allowed on a vsf port.

Event ID: 5738

Message
 Port <PORT_NAME> with fault-finder multicast-storm configuration cannot be added to a trunk.
Platforms WC, YA, YB, YC
Category System
Severity Information
Description This event is used to indicate fault-finder for multicast-storm is not allowed on a trunk port.

Event ID: 5741 (Severity: Warning)

Message
Fault-finder multicast-storm configuration is removed as it is configured on a VSF port <PORT_NUM>.
Platforms WC
Category System
Severity Warning
Description This event is used to indicate that fault-finder multicast-storm is not allowed on a VSF port.