Ports Events

The following are the events related to Ports.

Event ID: 76

Message
port <PORT_ID> is now on-line
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information
Description Indicates the port changed from an off-line to on-line state. To be on-line, the port must be both connected into the LAN and enabled through configuration. <id> is a letter-digit identifier (for example, A1 F3) where the letter represents the port module slot (A thru F) and the digit represents the port on the slot (1 thru 4 for Ethernet modules and 1 thru 2 for 100VG).

Event ID: 77

Message
port <PORT_ID> is now off-line
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information
Description Indicates the port changed from an on-line to off-line state. This occurs when the port is physically disconnected from the LAN, disabled through configuration, or both. <id> is a letter-digit identifier (for example, A1, F3) where the letter represents the port module slot (A thru F) and the digit represents the port on the slot (1 thru 4 for Ethernet modules and 1 thru 2 for 100VG).

Event ID: 78

Message
trunk <TRUNK_ID> is now active
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information
Description Indicates the port trunk has changed from an inactive to active state. This occurs when all ports in the trunk are off-line; and then one port comes on-line. <id> is always "Tr1" since there can be only one port trunk on the switch.

Event ID: 79

Message
trunk <TRUNK_ID> is now inactive
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information
Description Indicates the port trunk has changed from an active to inactive state. This occurs when the last on-line port in the trunk goes off-line such that there are now no ports in the trunk that are on-line. <id> is always "Tr1" since there can be only one port trunk on the switch.

Event ID: 255 (Severity: Warning)

Message
Cannot configure trunk <TRUNK_ID> - out of resources
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning
Description Cannot configure trunk TRUNK-ID; out of resources.

Event ID: 256

Message
Port <PORT_NUM> is reserved for <EVENT_MSG> use
Platforms K, KA, KB, WB, WC
Category Ports
Severity Information
Description This message displays during port-stealing.

Event ID: 257

Message
Port <PORT_NUM> is unreserved from <EVENT_MSG> use
Platforms K, KA, KB, WB, WC
Category Ports
Severity Information
Description This message displays during port-unstealing.

Event ID: 325 (Severity: Warning)

Message
Port initialization failed for port <PORT_NUM>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning
Description GVRP could not add a port to a VLAN because system has reached the maximum number of VPORT (port-vlan pairs) instances.

Event ID: 326 (Severity: Warning)

Message
port <PORT_NUM>: Xcvr not supported in current OS
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning
Description Port has been blocked on VLAN by PVST.

Event ID: 335

Message
port <PORT_NUM>: exceeded threshold broadcast throttling started
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information
Description The port has exceeded threshold broadcast so throttling has been started.

Event ID: 336

Message
port <PORT_NUM>: broadcast throttling stopped
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information
Description Broadcast throttling has been stopped on the port.

Event ID: 366 (Severity: Warning)

Message
port <PORT_NUM> Carrier Sense Stuck- Resetting Xcvr
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 368 (Severity: Warning)

Message
port <PORT_NUM> Xcvr Error- Resetting Xcvr ...
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 369 (Severity: Warning)

Message
port <PORT_NUM> Rx Signal/PLL Error- Resetting Xcvr R17: <ERROR_ID>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 370 (Severity: Warning)

Message
resetting port <PORT_NUM>: remote fault- ieee- parallel detect
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 378

Message
port <PORT_NUM>: Slot <SLOT_ID> Interrupt <INTERUPT_ID>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 379

Message
port <PORT_NUM> in half duplex- flow control is auto-disabled.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 405

Message
port <PORT_NUM> xcvr hot-swap insert.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 406

Message
port <PORT_NUM> xcvr hot-swap remove.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 407

Message
port <PORT_NUM> new xcvr invalid type and/or speed.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 408

Message
port <PORT_NUM> xcvr type change. Check switch config.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 409

Message
port <PORT_NUM> GigT xcvr invalid mode change. Need reboot.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 435

Message
port <PORT_NUM> is Blocked by <EVENT STR>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information
Description Indicates that the port is being blocked

Event ID: 448 (Severity: Warning)

Message
port <PORT_NUM> disabled due to faulty link partner. Re-install module or reset switch prior to re-enabling port.
Platforms K, KA, KB, WB, WC, YC
Category Ports
Severity Warning
Description The port was disabled due to faulty link partner. Re-install module or reset switch prior to re-enabling port.

Event ID: 449

Message
port <PORT_NUM> RJ-45 is enabled.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 450

Message
port <PORT_NUM> mini-GBIC is enabled.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 532 (Severity: Warning)

Message
port <PORT_NUM> Unsupported Transceiver. (SelfTest Err#<ERROR ID>)
Check: http://www.arubanetworks.com/products/networking/ for more info.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 533 (Severity: Warning)

Message
port <PORT_NUM> is not a <TYPE> transceiver. Please go to: http://www.arubanetworks.com/products/networking/ for more info.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning
Description Unsupported OUI or SFP type verbiage

Event ID: 534 (Severity: Warning)

Message
port <PORT_NUM> Transceiver type not supported in this software  version. Please check for an updated release.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 535 (Severity: Warning)

Message
port <PORT_NUM> This switch only supports revision B and above transceivers.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 536 (Severity: Warning)

Message
port <PORT_NUM> Transceiver type not supported in this port.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 560

Message
port <PORT_NUM> PD Detected.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 561

Message
port <PORT_NUM> Applying Power to PD.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 562 (Severity: Warning)

Message
port <PORT_NUM> PD Over Current indication.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 563 (Severity: Warning)

Message
port <PORT_NUM> PD MPS Absent indication.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 564 (Severity: Warning)

Message
port <PORT_NUM> PD Invalid Signature indication.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 565

Message
port <PORT_NUM> PD Removed.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 566 (Severity: Warning)

Message
port <PORT_NUM> PD Denied power due to insufficient power allocation.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 567 (Severity: Warning)

Message
port <PORT_NUM> PD Other Fault indication.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 580 (Severity: Warning)

Message
Port <PORT_NUM>: Attempt to recover from bad FET failed. The port will not deliver power.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 632 (Severity: Warning)

Message
port <PORT_NUM> Duplex Mismatch. Reconfig port to Full Duplex.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 633 (Severity: Warning)

Message
port <PORT_NUM> Duplex Mismatch. Reconfig port to Auto.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 723 (Severity: Warning)

Message
Port <PORT_NUM> both flow ctrl and jumbo frames enabled. Flow control may not function properly.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 898

Message
<SYSTEM ID> has disabled port <PORT_NUMBER> for <TIMEOUT> seconds
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 899 (Severity: Warning)

Message
<SYSTEM ID> has disabled port <PORT_NUM>
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 900

Message
Port <PORT_NUM> timer requested by <SYSTEM ID> has expired
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 927 (Severity: Warning)

Message
Port <PORT_ID> - Port Security configured on a 10Mbps port-          packets will be dropped. Refer to switch manuals.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 2562 (Severity: Warning)

Message
Port <PORT_NUM>: Possible bad FET/PSE supplying PoE power - suggest configuring other end of link with "no power"
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 2566 (Severity: Warning)

Message
Port <PORT_NUM>: Recovered from bad FET.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 2567 (Severity: Warning)

Message
Port <PORT_NUM>: Possible bad FET - suggest resetting with "power poe-reset". Or- PSE supplying PoE power - suggest configuring other end of link with "no power"
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 2767 (Severity: Warning)

Message
port <PORT_NUM> detected non-HPID xcvr or DAC
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 2768 (Severity: Warning)

Message
Port <PORT_NUM> PoE power dropped. Exceeded physical classification for a PoE Type1 device (LLDP process disabled)
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 2770 (Severity: Warning)

Message
Port <PORT_NUM> EEE disabled due to Polarity Error found on the cable. Correct the polarity error for EEE to work.
Platforms K, KA, KB, WB, WC, YA, YC
Category Ports
Severity Warning

Event ID: 2771 (Severity: Warning)

Message
Port <PORT_NUM> PoE power dropped. Exceeded physical classification due to change in classification type (LLDP process enabled)
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 2772 (Severity: Warning)

Message
EEE cannot be enabled on port <PORT_NUM> on this hardware revision- (link partner attempted to enable).
Platforms K, KA, KB, WB, WC, YA, YC
Category Ports
Severity Warning

Event ID: 3169 (Severity: Warning)

Message
Only <MAX_LIMIT> <PRODUCT_NUMBER> transceivers are supported in this module. The transceiver in port <PORT_NUM> has been disabled. Please remove this transceiver.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning
Description Logs a port having a transceiver over its restriction limit

Event ID: 3700

Message
Non-HP transceiver detected in port <PORT_NUM>- which may cause network problems. HP will not support or troubleshoot problems with this transceiver.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 3701

Message
Ports <PORT_NUM> still has unsupported transceivers- which may cause network problems.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 3702

Message
Port <PORT_NUM> - port type change. The port configuration may need to be updated.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 3703

Message
Port <PORT_NAME> unsupported xcvr hot-swap insert.
Platforms KB, WB, WC, YA, YB, YC
Category Ports
Severity Information
Description A third party transceiver has been swapped into one of the transceiver bay.

Event ID: 3704

Message
Allow-Unsupported-Transceiver feature enabled:
Platforms KB, WB, WC, YA, YB, YC
Category Ports
Severity Information
Description Unsupported Transceivers found in: <EVENT_MSG> List of Non-HPN transceiver has been present into the switch.

Event ID: 3705

Message
Allow-Unsupported-Transceiver feature enabled.
Platforms KB, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 4742 (Severity: Warning)

Message
PTP temporarily disabled on port <PORT_ID> - IEEE 1588 is not supported at the current link speed
Platforms KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning
Description Port <PORT_ID> is linked up with the speed at which we don't support IEEE1588 protocol

Event ID: 4743

Message
Port <PORT_NUM> recovery occurred.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 4744 (Severity: Warning)

Message
PTP disabled on all ports - the inserted module does not support IEEE 1588
Platforms KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 4745 (Severity: Warning)

Message
PTP disabled on all ports - this software version does not support enabling MACsec and IEEE 1588 at the same time
Platforms KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 4776

Message
Connection-rate filter is disabled because meshing is enabled on port <PORT_ID>.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Information

Event ID: 5100 (Severity: Warning)

Message
port <PORT_NUM> encountered a UVLO fault and will attempt to recover itself by toggling power.
Platforms K, KA, KB, RA, WB, WC, YA, YB, YC
Category Ports
Severity Warning

Event ID: 5176

Message
Port <PORT_NAME>: Configuring poe-value <POE_VALUE> to maximum supported value 30.
Platforms KB, WC, YC
Category Ports
Severity Information
Description If poe-value greater than 30 is configured in previous release, while upgrading to 16.01 it is converted to 30 and below log is generated- Port <PORT_NAME>: Configuring poe-value <POE_VALUE> to maximum supported value 30.

Event ID: 5761 (Severity: Warning)

Message
Port <PORT_NAME_STRING> [chan <CHANNEL>]: Possible bad FET/PSE supplying PoE power - suggest configuring other end of link with "no power"
Platforms WC
Category Ports
Severity Warning
Description Informs about possible faulty FET/PSE supplying PoE power. Configure other end of link with "no power" on port on a channel.

Event ID: 5762 (Severity: Warning)

Message
Port <PORT_NAME_STRING> [chan <CHANNEL>]: Recovered from bad FET.
Platforms WC
Category Ports
Severity Warning
Description Informs to recover from faulty FET.

Event ID: 5763 (Severity: Warning)

Message
Port <PORT_NAME_STRING> [chan <CHANNEL>]: Attempt to recover from bad FET failed. The port will not deliver power.
Platforms WC
Category Ports
Severity Warning
Description Informs to attempt to recover from faulty FET failure. The port does not deliver power.

Event ID: 5764 (Severity: Warning)

Message
Port <PORT_NAME_STRING> [chan <CHANNEL>]: PD Over Current indication.
Platforms WC
Category Ports
Severity Warning
Description Informs the PD Over Current indication for port on a channel.

Event ID: 5773

Message
Port <PORT_NAME_STRING>: Dual Signature PD Detected.
Platforms WC
Category Ports
Severity Information
Description Indicates that the Dual Signature PD is detected.

Event ID: 5774

Message
Port <PORT_NAME_STRING> [chan <CHANNEL>]: Applying Power to PD.
Platforms WC
Category Ports
Severity Information
Description Indicates that the Power to PD is applied.

Event ID: 5775 (Severity: Warning)

Message
Port <PORT_NAME_STRING> [chan <CHANNEL>]: PD MPS Absent indication.
Platforms WC
Category Ports
Severity Warning
Description Indicates the PD MPS is absent.

Event ID: 5776 (Severity: Warning)

Message
 Port <PORT_NAME_STRING> [chan <CHANNEL>]: PD Invalid Signature detected.
Platforms WC
Category Ports
Severity Warning
Description Indicates a PD Invalid Signature.

Event ID: 5777

Message
Port <PORT_NAME_STRING> [chan <CHANNEL>]: PD Removed.
Platforms WC
Category Ports
Severity Information
Description Indicates a PD is removed.

Event ID: 5778 (Severity: Warning)

Message
Port <PORT_NAME_STRING> [chan <CHANNEL>]: Power denied due to Power On Verification fault.
Platforms WC
Category Ports
Severity Warning
Description Indicates the power is denied due to Power On Verification fault.

Event ID: 5779 (Severity: Warning)

Message
Port <PORT_NAME_STRING>: PD power <CHANNEL>. Suggest using allocate-by-usage or allocate-by-class
Platforms WC
Category Ports
Severity Warning

Event ID: 5780

Message
Port <PORT_NAME_STRING> [chan <CHANNEL>]: Power demoted.
Platforms WC
Category Ports
Severity Information
Description Indicates the power is demoted.

Event ID: 5781

Message
Port <PORT_NAME_STRING>: 802.3bt non-compliant Dual Signature PD Detected.
Platforms WC
Category Ports
Severity Information
Description Indicates the 02.3bt non-compliant Dual Signature PD is detected.

Event ID: 5782

Message
Port <PORT_NAME_STRING>: Power demoted.
Platforms WC
Category Ports
Severity Information
Description Indicates the power is demoted.

Event ID: 5783 (Severity: Warning)

Message
Port <PORT_NAME_STRING> [chan <CHANNEL>]: Power denied due to Power On Invalid Class Sequence.
Platforms WC
Category Ports
Severity Warning
Description Indicates the power denied event due to power On Invalid Class Sequence.