Viewing the running configuration of interfaces
To view the running configuration of interfaces, do one of the following:
Procedure
Examples
The following example shows Running configuration output in preview mode.switch(config)# preview-mode
ATTENTION: You are entering preview mode on this product. This mode, the
commands, features and functionality specific to this mode, and all output
from this mode are Hewlett Packard Enterprise Confidential and Proprietary.
You may use this mode at your own risk. Any defects or issues encountered
in this mode will be addressed per Hewlett Packard Enterprise's discretion.
Continue (y/n)? y
(Prev-mode)switch(config)# show running-config
Running configuration:
; JL075A Configuration Editor; Created on release #KB.16.01.0000x
; Ver #0c:01.7c.59.f4.7b.ff.ff.fc.ff.ff.3f.ef:
hostname "Aruba-3810M-16SFPP-2s"
module 1 type jl075x
module 2 type jl075y
module 3 type jl075z
snmp-server community "public" unrestricted
oobm
ip address dhcp-bootp
exit
vlan 1
name "DEFAULT_VLAN"
untagged 1-16
ip address dhcp-bootp
exit
preview-mode
The following example shows Running configuration output for interfaces A2 - A4
switch(eth-A2-A4)# show running-config
Running configuration:
; J8698A Configuration Editor; Created on release #K.15.10.0001
; Ver #02:0b:ef:e6
hostname "switch"
interface A2
disable
name "test1"
flow-control
broadcast-limit 80
speed-duplex 100-full
unknown-vlans Block
qos priority 4
lacp Passive
gvrp join-timer 30
gvrp leave-timer 60
gvrp leaveall-timer 700
exit
interface A3
disable name "test1"
flow-control
broadcast-limit 80
speed-duplex 100-full
unknown-vlans Block
qos priority 4
lacp Passive
gvrp join-timer 30
gvrp leave-timer 60
gvrp leaveall-timer 700
exit
vlan 1
name "DEFAULT_VLAN"
untagged A1-A4,C1-C24,F1-F4
ip address dhcp-bootp
exit
interface A2
dhcp-snooping trust
bandwidth-min output 20 10 10 10 20 10 10 10
rate-limit bcast in percent 75
ipv6 access-group "check" in
exit
interface A3
dhcp-snooping trust
bandwidth-min output 20 10 10 10 20 10 10 10
rate-limit bcast in percent 75
ipv6 access-group "check" in
exit
The following example shows an example of the running config for a range of interfaces. The configuration information for interfaces A2 and A3 is now displayed together.
switch(config)# show running-config interface A2-A3
Running configuration:
interface A2
disable
name "test1"
flow-control
broadcast-limit 80
speed-duplex 100-full
unknown-vlans block
qos priority 4
gvrp join-timer 30 leave-timer 60 leaveall-timer 700
dhcp-snooping trust
lacp passive
bandwidth-min output 20 10 10 10 20 10 10 10
rate-limit bcast in percent 75
ipv6 access-group "check" in
untagged vlan 1
exit
interface A3
disable
name "test1"
flow-control
broadcast-limit 80
speed-duplex 100-full
unknown-vlans block
qos priority 4
gvrp join-timer 30 leave-timer 60 leaveall-timer 700
dhcp-snooping trust
lacp passive
bandwidth-min output 20 10 10 10 20 10 10 10
rate-limit bcast in percent 75
ipv6 access-group "check" in
untagged vlan 1
exit
The following example shows an example of the running config file for a range of interfaces after some configuration changes have been made.
switch(config)# no stack
switch(config)# mesh 2-3
Command will take effect after saving configuration and reboot.
switch(config)# write memory
switch(config)# reload
switch# show running-config interface 2-3
Running configuration:
interface 2
untagged vlan 1
mesh
exit
interface 3
flow-control
untagged vlan 1
mesh
exit
The following example is an example of the running config output showing VLAN information.
switch(config)# show running-config
Running configuration:
; J8698A Configuration Editor; Created on release #K.15.10.0001
; Ver #02:0b:ef:e6
hostname "switch"
module 1 type J9309A
module 3 type J8702A
module 6 type J8702A
ip routing
vlan 1
name "DEFAULT_VLAN"
untagged A1-A4,C1-C24,F1-F24
ip address dhcp-bootp
exit
vlan 2
name "test-vlan-2"
ip helper-address 4.1.1.1
ip helper-address 5.1.1.1
ip address 1.1.1.1 255.255.255.0
ipv6 address 2001::/64 anycast
ipv6 enable
exit
vlan 3
name "VLAN3"
ip helper-address 7.1.1.1
ip forward-protocol udp 7.1.1.1 snmp
ip forward-protocol udp 11.1.1.2 dns
no ip address
exit
vlan 4
name "VLAN4"
ip address 5.1.1.1 255.255.255.0
ip bootp-gateway 5.1.1.1
exit
logging 10.0.102.90
logging system-module ospf
ip route 5.1.1.0 255.255.255.0 vlan 4 distance 3
In the following example, the configuration information for VLAN 4 is now displayed in one place.
switch(config)# show running-config vlan 3-4
Running configuration:
vlan 3
name "VLAN3"
ip helper-address 7.1.1.1
ip forward-protocol udp 7.1.1.1 snmp
ip forward-protocol udp 11.1.1.2 dns
no ip address
exit
vlan 4
name "VLAN4"
ip address 5.1.1.1 255.255.255.0
ip bootp-gateway 5.1.1.1
ip route 5.1.1.0 255.255.255.0 distance 3
exit
Below is an example of the running config for a range of VLANs after configuration changes have been made to selected VLANs.
switch(config)# dhcp-snooping
switch(config)# vlan 14
switch(vlan-14)# exit
switch(config)# vlan 15
switch(vlan-15)# exit
switch(config)# vlan 23
switch(vlan-23)# exit
switch(config)# dhcp-snooping vlan 14-15
switch(config)# static-mac 00:11:22:33:44:55 vlan 23 interface A3
switch(config)# spanning-tree instance 2 vlan 15
switch(config)# show running-config vlan 14-15
Running configuration:
vlan 14
name "VLAN14"
no ip address
dhcp-snooping
exit
vlan 15
name "VLAN15"
no ip address
dhcp-snooping
spanning-tree instance 2
exit