Ports Events
The following are the events related to Ports.
Event ID: 76
Message | port <PORT_ID> is now on-line |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | Indicates the port changed from an off-line to on-line state. To be on-line, the port must be both connected into the LAN and enabled through configuration. <id> is a letter-digit identifier (for example, A1 F3) where the letter represents the port module slot (A thru F) and the digit represents the port on the slot (1 thru 4 for Ethernet modules and 1 thru 2 for 100VG). |
Event ID: 77
Message | port <PORT_ID> is now off-line |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | Indicates the port changed from an on-line to off-line state. This occurs when the port is physically disconnected from the LAN, disabled through configuration, or both. <id> is a letter-digit identifier (for example, A1, F3) where the letter represents the port module slot (A thru F) and the digit represents the port on the slot (1 thru 4 for Ethernet modules and 1 thru 2 for 100VG). |
Event ID: 78
Message | trunk <TRUNK_ID> is now active |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | Indicates the port trunk has changed from an inactive to active state. This occurs when all ports in the trunk are off-line; and then one port comes on-line. <id> is always "Tr1" since there can be only one port trunk on the switch. |
Event ID: 79
Message | trunk <TRUNK_ID> is now inactive |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | Indicates the port trunk has changed from an active to inactive state. This occurs when the last on-line port in the trunk goes off-line such that there are now no ports in the trunk that are on-line. <id> is always "Tr1" since there can be only one port trunk on the switch. |
Event ID: 255 (Severity: Warning)
Message | Cannot configure trunk <TRUNK_ID> - out of resources |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | Cannot configure trunk TRUNK-ID; out of resources. |
Event ID: 256
Message | Port <PORT_NUM> is reserved for <EVENT_MSG> use |
Platforms | K, KA, KB, WB, WC |
Category | Ports |
Severity | Information |
Description | This message displays during port-stealing. |
Event ID: 257
Message | Port <PORT_NUM> is unreserved from <EVENT_MSG> use |
Platforms | K, KA, KB, WB, WC |
Category | Ports |
Severity | Information |
Description | This message displays during port-unstealing. |
Event ID: 325 (Severity: Warning)
Message | Port initialization failed for port <PORT_NUM> |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | GVRP could not add a port to a VLAN because system has reached the maximum number of VPORT (port-vlan pairs) instances. |
Event ID: 326 (Severity: Warning)
Message | port <PORT_NUM>: Xcvr not supported in current OS |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | Port has been blocked on VLAN by PVST. |
Event ID: 335
Message | port <PORT_NUM>: exceeded threshold broadcast throttling started |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | The port has exceeded threshold broadcast so throttling has been started. |
Event ID: 336
Message | port <PORT_NUM>: broadcast throttling stopped |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | Broadcast throttling has been stopped on the port. |
Event ID: 366 (Severity: Warning)
Message | port <PORT_NUM> Carrier Sense Stuck- Resetting Xcvr |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 368 (Severity: Warning)
Message | port <PORT_NUM> Xcvr Error- Resetting Xcvr ... |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 369 (Severity: Warning)
Message | port <PORT_NUM> Rx Signal/PLL Error- Resetting Xcvr R17: <ERROR_ID> |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 370 (Severity: Warning)
Message | resetting port <PORT_NUM>: remote fault- ieee- parallel detect |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 378
Message | port <PORT_NUM>: Slot <SLOT_ID> Interrupt <INTERUPT_ID> |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 379
Message | port <PORT_NUM> in half duplex- flow control is auto-disabled. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 405
Message | port <PORT_NUM> xcvr hot-swap insert. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 406
Message | port <PORT_NUM> xcvr hot-swap remove. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 407
Message | port <PORT_NUM> new xcvr invalid type and/or speed. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 408
Message | port <PORT_NUM> xcvr type change. Check switch config. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 409
Message | port <PORT_NUM> GigT xcvr invalid mode change. Need reboot. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 435
Message | port <PORT_NUM> is Blocked by <EVENT STR> |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | Indicates that the port is being blocked |
Event ID: 448 (Severity: Warning)
Message | port <PORT_NUM> disabled due to faulty link partner. Re-install module or reset switch prior to re-enabling port. |
Platforms | K, KA, KB, WB, WC, YC |
Category | Ports |
Severity | Warning |
Description | The port was disabled due to faulty link partner. Re-install module or reset switch prior to re-enabling port. |
Event ID: 449
Message | port <PORT_NUM> RJ-45 is enabled. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 450
Message | port <PORT_NUM> mini-GBIC is enabled. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 532 (Severity: Warning)
Message | port <PORT_NUM> Unsupported Transceiver. (SelfTest Err#<ERROR ID>) Check: http://www.arubanetworks.com/products/networking/ for more info. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 533 (Severity: Warning)
Message | port <PORT_NUM> is not a <TYPE> transceiver. Please go to: http://www.arubanetworks.com/products/networking/ for more info. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | Unsupported OUI or SFP type verbiage |
Event ID: 534 (Severity: Warning)
Message | port <PORT_NUM> Transceiver type not supported in this software version. Please check for an updated release. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 535 (Severity: Warning)
Message | port <PORT_NUM> This switch only supports revision B and above transceivers. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 536 (Severity: Warning)
Message | port <PORT_NUM> Transceiver type not supported in this port. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 560
Message | port <PORT_NUM> PD Detected. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 561
Message | port <PORT_NUM> Applying Power to PD. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 562 (Severity: Warning)
Message | port <PORT_NUM> PD Over Current indication. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 563 (Severity: Warning)
Message | port <PORT_NUM> PD MPS Absent indication. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 564 (Severity: Warning)
Message | port <PORT_NUM> PD Invalid Signature indication. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 565
Message | port <PORT_NUM> PD Removed. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 566 (Severity: Warning)
Message | port <PORT_NUM> PD Denied power due to insufficient power allocation. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 567 (Severity: Warning)
Message | port <PORT_NUM> PD Other Fault indication. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 580 (Severity: Warning)
Message | Port <PORT_NUM>: Attempt to recover from bad FET failed. The port will not deliver power. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 632 (Severity: Warning)
Message | port <PORT_NUM> Duplex Mismatch. Reconfig port to Full Duplex. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 633 (Severity: Warning)
Message | port <PORT_NUM> Duplex Mismatch. Reconfig port to Auto. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 723 (Severity: Warning)
Message | Port <PORT_NUM> both flow ctrl and jumbo frames enabled. Flow control may not function properly. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 898
Message | <SYSTEM ID> has disabled port <PORT_NUMBER> for <TIMEOUT> seconds |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 899 (Severity: Warning)
Message | <SYSTEM ID> has disabled port <PORT_NUM> |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 900
Message | Port <PORT_NUM> timer requested by <SYSTEM ID> has expired |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 927 (Severity: Warning)
Message | Port <PORT_ID> - Port Security configured on a 10Mbps port- packets will be dropped. Refer to switch manuals. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 2562 (Severity: Warning)
Message | Port <PORT_NUM>: Possible bad FET/PSE supplying PoE power - suggest configuring other end of link with "no power" |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 2566 (Severity: Warning)
Message | Port <PORT_NUM>: Recovered from bad FET. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 2567 (Severity: Warning)
Message | Port <PORT_NUM>: Possible bad FET - suggest resetting with "power poe-reset". Or- PSE supplying PoE power - suggest configuring other end of link with "no power" |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 2767 (Severity: Warning)
Message | port <PORT_NUM> detected non-HPID xcvr or DAC |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 2768 (Severity: Warning)
Message | Port <PORT_NUM> PoE power dropped. Exceeded physical classification for a PoE Type1 device (LLDP process disabled) |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 2770 (Severity: Warning)
Message | Port <PORT_NUM> EEE disabled due to Polarity Error found on the cable. Correct the polarity error for EEE to work. |
Platforms | K, KA, KB, WB, WC, YA, YC |
Category | Ports |
Severity | Warning |
Event ID: 2771 (Severity: Warning)
Message | Port <PORT_NUM> PoE power dropped. Exceeded physical classification due to change in classification type (LLDP process enabled) |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 2772 (Severity: Warning)
Message | EEE cannot be enabled on port <PORT_NUM> on this hardware revision- (link partner attempted to enable). |
Platforms | K, KA, KB, WB, WC, YA, YC |
Category | Ports |
Severity | Warning |
Event ID: 3169 (Severity: Warning)
Message | Only <MAX_LIMIT> <PRODUCT_NUMBER> transceivers are supported in this module. The transceiver in port <PORT_NUM> has been disabled. Please remove this transceiver. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | Logs a port having a transceiver over its restriction limit |
Event ID: 3700
Message | Non-HP transceiver detected in port <PORT_NUM>- which may cause network problems. HP will not support or troubleshoot problems with this transceiver. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 3701
Message | Ports <PORT_NUM> still has unsupported transceivers- which may cause network problems. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 3702
Message | Port <PORT_NUM> - port type change. The port configuration may need to be updated. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 3703
Message | Port <PORT_NAME> unsupported xcvr hot-swap insert. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | A third party transceiver has been swapped into one of the transceiver bay. |
Event ID: 3704
Message | Allow-Unsupported-Transceiver feature enabled: |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Description | Unsupported Transceivers found in: <EVENT_MSG> List of Non-HPN transceiver has been present into the switch. |
Event ID: 3705
Message | Allow-Unsupported-Transceiver feature enabled. |
Platforms | KB, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 4742 (Severity: Warning)
Message | PTP temporarily disabled on port <PORT_ID> - IEEE 1588 is not supported at the current link speed |
Platforms | KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Description | Port <PORT_ID> is linked up with the speed at which we don't support IEEE1588 protocol |
Event ID: 4743
Message | Port <PORT_NUM> recovery occurred. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 4744 (Severity: Warning)
Message | PTP disabled on all ports - the inserted module does not support IEEE 1588 |
Platforms | KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 4745 (Severity: Warning)
Message | PTP disabled on all ports - this software version does not support enabling MACsec and IEEE 1588 at the same time |
Platforms | KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 4776
Message | Connection-rate filter is disabled because meshing is enabled on port <PORT_ID>. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Information |
Event ID: 5100 (Severity: Warning)
Message | port <PORT_NUM> encountered a UVLO fault and will attempt to recover itself by toggling power. |
Platforms | K, KA, KB, RA, WB, WC, YA, YB, YC |
Category | Ports |
Severity | Warning |
Event ID: 5176
Message | Port <PORT_NAME>: Configuring poe-value <POE_VALUE> to maximum supported value 30. |
Platforms | KB, WC, YC |
Category | Ports |
Severity | Information |
Description | If poe-value greater than 30 is configured in previous release, while upgrading to 16.01 it is converted to 30 and below log is generated- Port <PORT_NAME>: Configuring poe-value <POE_VALUE> to maximum supported value 30. |