Validation rules

Validation

Error/Warning/Prompt

Enabling SLA without configuring SLA type.

Cannot enable IP SLA, no valid source/destination configured.

IP address given for source or destination is multicast or broadcast.

Invalid IP address.

Configure the SLA type with a source IP which is configured in the same switch.

Destination IP cannot be configured as the same as one of the local interface IP addresses.

Configure threshold with invalid value.

Invalid threshold count value. For threshold type 'Immediate', count must be 1 and for 'Consecutive', count must be greater than or equals to 2.

Configure threshold value for 'PacketLoss' or 'TestCompletion'

Configuration is not applicable when threshold is configured for 'PacketLoss' or 'TestCompletion'.

Configure threshold type for TestCompletion.

Configuration is not applicable when threshold is configured for 'TestCompletion'.

Configure schedule with proper end time with a frequency which is out of end time.

Invalid endtime. Endtime is not enough to run the tests for configured frequency and repetitions.

Configuring ‘srcTodstTime’ or ‘dstTosrcTime’ threshold configuration for ‘icmp-echo’ or ‘tcp-connect’.

Invalid threshold configuration for configured SLA type.

Enabling the IP SLA which is already in enabled state.

IP SLA is already enabled.

Disabling the IP SLA which is already in disabled state.

IP SLA is already disabled.

Show IP SLA history of un-configured SLA.

IP SLA is not configured for this ID.

Enable more number (currently decided 50 as limit) of IP SLA.

Maximum number of enabled IP SLAs at a time is limited to 50.

Removing IP SLA type/tos/history size/schedule/ threshold configuration with un-configured value.

IP SLA configuration does not exist.

Configuring scheduler with a frequency value which is not satisfying the condition frequency > number of packets per probe * packet interval.

Frequency value is insufficient to configure the scheduler.

Scheduler already configured and try to configure SLA type with a value of ‘number of packets per probe’ and ‘packet interval’ which is not satisfying the condition frequency > number of packets per probe * packet interval.

Number of packets/packet interval is insufficient to configure IP SLA type.

Configuring IP SLA with invalid values.

Invalid configuration for IP SLA.

Change the IP SLA configuration when the SLA is enabled.

Configuration changes not allowed when IP SLA is enabled.

When IP address vs port number configured for an SLA is already in use

Error: Socket for configured address, port is already in use, choose different port number

When Source IP address given in SLA configuration is not configured in the switch

Error: Source IP address is not configured in switch

Invalid SLA ID given in show command

Error: Invalid IP SLA ID

Configure SLA more than allowed limit

Warning: The maximum number of IP SLAs allowed is 50.

Configure Responder more than allowed limit

Error: IP SLA Responder configurations reached max limit. No more configurations accepted.

Configure inter-packet interval when number of packets to be sent out is one.

Error Not applicable as Number of packets to be sent out is 1.

Upper threshold value is less than lower threshold value.

Error: Upper threshold value X is less than lower threshold value Y.

Configure schedule with start time greater than stop time.

Error: Stop time must be greater than start time.

Configure schedule with past stop time.

Error: Stop time must be greater than current time.

Configure schedule with invalid frequency value.

Error: Schedule frequency is out of range. Valid range is 5 to 604800.

Configuring history size with invalid value.

Error: IP SLA History size is out of range. Valid range is 1–50.

Configuring SLA type with invalid payload value.

IP SLA Payload value is out of range. Valid range is 1–1440.

Configuring SLA type with invalid port number.

Invalid port number. Valid range is 1024 to 65535.

Configure the IPSLA parameters without configuring SLA type.

No valid IP SLA type configuration found.

Configuring the responder with existing details.

IP SLA Responder with same configuration exist.

Configure management VLAN as source VLAN.

Error: Not allowed to configure management VLAN as source interface.

Enabling IP SLA without required configuration parameters.

Configuration is incomplete to enable the entry.

Configure IPSLA UDP Jitter/VoIP session when an OpenFlow custom match mode instance is already enabled.

Cannot enable IP SLA: Initiator cannot co-exist with OpenFlow custom Cannot enable IP SLA: Initiator cannot co-exist with OpenFlow custom

Configure UDP Jitter/VoIP IPSLA Initiator session with a source IP same as tunnel overlay VLAN

Cannot enable IP SLA: The source VLAN cannot be a tunnel overlay VLAN.

Configure UDP Jitter/VoIP IPSLA Initiator session with a source IP same as a service tunnel endpoint.

Cannot enable IP SLA: The source VLAN cannot be a service tunnel endpoint.